©By: John T. Blair (WA4OHZ)
1133 Chatmoss Dr., Va. Beach, Va. 23464; (757) 495-8229
Last update: 01/30/2000
The nuts and bolts on my Morgan were Whitworth and British standard. During this restoration, I decided to replace most of the nuts and bolts. However, in stead of using the British types or metric, I replaced them with the closest SAE (American) counter part I could find as listed below.
Double - 7 - 3 rear, 3 mid, 1 front harness
Single - 11 - 2 rear, 2 mid, 3 front right, 3 front left, 1 heater.
I recommend that most of these be Stainless Steel as they don't rust and can be polished. While the cost is slightly more, it is not that much more!.
#4 x 1/2" Flat head wood screws Note: Sheet metal
200 sheet metal panels to wood subframe screws can be used
instead of wood screws
#4 x 3/4" Flat head wood screws
50 Attach the wooden trunk back to wood subframe
#8 x 3/8" Pan head sheet metal screws
12 Turn signal to body (3 per turn signal)
#8 x 1/2" Round head wood screws
12+ Hold clamps for wiring & fuel line
#8 x 5/8" Pan head sheet metal screws
8 Headlight to body (4 per headlight)
#8 x 3/4" Round head wood screws
6 Transmission cover to floor boards
8 Door latches
8 Door check straps
25 Firewall to wood subframe
#8 x 3/4" Panhead
1 Fuse holder to firewall
#8 x 3/4" Oval head Phillips
18 Read Deck to Cap strip
2 Head light outer chrome Rim
12 Side curtain brackets to door
#8 x 1" - Flat head wood screws
4 Top bows to wood subframe
4 Door striker plate to wood subframe
12 Door arm rest rail to door
16 Door hinges
#8 x 2" - Flat head wood screws
4 Wood blocks that form the slot for bench seat back
#8 Flat washers
25 Firewall to wood frame
#10 x 1/2" - Flat head - Phillips - (MUST be 32TPI)
8 Steering wheel
#10 x 1/2" - Round head machine screws and nuts
12 To secure the bonnet knob backing plate to the hood
11 Misc on firewall
#10 x 1/2 - Filister head machine screw & nut
4 2 per tail light to attach to fenders.
#10 x 1/2 - Pan head - Phillips slot
4 2 per tail light to attach tail light lens.
#10 x 3/4" - Round head machine screws and bolts
10 Transmission cover to firewall
2 License plate light bracket to rear deck
#10 - 24 x 3/4" - Pan head machine screws
10 Rear fenders to fender arches
#10 x 3/4" - Round head wood screws - Slotted head **UPDATED**
25 Firewall to wood frame - Can use instead of the #8s
#10 - 24 x 1" - Pan head machine screws Note: Should have a
10 Rear fenders to fender arches couple 1 1/2" to
initially get fenders
up
#10 x 1" - Round head machine screws, bolts and fender washers
24 Top of front fenders to inner fender panel (Try 1/2 or 3/4")
#10 x 1" - Hex head machine screws and nuts (same as 3/16 dia. bolt)
12 Nose to front fenders
#10 x 1" Hex head /w shoulder sheet metal screws
16 Rear of front fender to bottom of sill plate
#10 x 1 1/4" - Flat head wood screws
12 Door hinges to doors & door post
#10 x 1 1/4" - Round head machine screws and bolts
2 Voltage Regulator to firewall
#10 x 1 1/2" - Round head machine screws and bolts Note: I used #10 x 1"
16 Rear Wings (fenders) to wood arches hex head /w shoulder
8 Rear of front fender to lower door frame sheet metal screws.
#10 x 2" - Flat head machine screws & nuts
4 One each side of each hinge - through door hinge pillar
#10 - Fender washers - 1 box
#10-24 - T nuts
16 Hold rear fender to arches
3/16 x 24 x 1/2" - Flat head bolts & nuts
3 accelerator pedal to firewall
1/4 x 1/2" - Hex head nuts & bolts
6 Front inner fender well (rear) to firewall
4 Al. steering wheel support bracket on front of firewall
4 Grill support bracket to valances
3 Grill to bracket
1/4 x 5/8" - Hex head bolts
4 windshield to support on cowl
1/4 x 3/4" - Hex head nuts & bolts - Grade 8
8 Rear shock plates
4 Rear motor mount bracket
1/4 x 3/4" - Hex head nuts & bolts
10 Firewall to chassis
2 Emergency brake mounting plate
12 Valances (front inner fender panel) to chassis
1/4 x 1" - Hex head nuts & bolts
8 Front bumper horn caps
4 Valances to chassis - steering dampener attachment and aluminum
block
1/4 x 1" Oval head machine screws
4 Windshield to cowl (2 per side)
1/4 x 1 3/4" - Hex head nuts & bolts
2 cross wise on steering col. support on front of firewall
1/4" - Fender washers - 1 box
5/16 x 3/4" - Hex head nuts & bolts (GRADE 8)
4 Rear drive shaft coupling (to differential)
2 Front end drag link to chassis
5/16 x 1" - Hex head bolts
4 Radiator Support brackets to Chassis
5/16 x 1" - Hex head nuts & bolts (GRADE 8)
4 Kingpin lower mount (2 each side)
10 Front subframe to Chassis
6 Engine mounts to Chassis
5/16 x 1" - Hex head bolt (MUST be 18 TPI)
4 Bumper overrider to bumper
5/16 x 1" - Hex head bolt (MUST be 24 TPI)
4 1 per bumper overrider to bumper bracket
5/16 x 1 1/4" - Hex head bolts - must be 18 TP
2 Master cylinder to mounting block
5/16 x 1 3/4 (to 2") - Hex head nuts & bolts
3 Master cylinder to chassis
5/16 x 2 1/2" - Hex head nuts & bolts
2 Steering col.. support block under dashboard
2 Radiator to radiator supports
3/8 x 1" - Hex head nuts & bolts (GRADE 8)
4 Rear shock (2 per shock)
3/8 x 1" - Hex head nuts & bolts
4 Rear Bumper support bracket to bumper mount & chassis
2 Rear bumper to chassis
1/4 - 20 x 1/2" - Round head screws
4 Valve cover to head
1/4 - 20 x 1/2" - Hex head bolt
1 Distributor clamp to block
1/4 - 20 x 3/4" - Hex head bolts
16 Oil pan to block
1/4 - 20 x 5/8" - Hex head bolts
4 Fan to H20 pump
1/4 - 20 x 7/8" - Hex head bolts
4 Timing chain cover to block
1/4 - 20 x 1 7/8" - Hex head bolts
3 H2O pump to block
1/4 - 20 x 2 1/4" - Hex head bolts
2 Rear Oil pan to block
5/16 - 18 x 1" - Hex head bolts
8 Motor mounts to block
3 Oil pump to block
4 Top inner manifold
5/16 - 18 x 1 1/2" - Hex head bolts
2 Outer lower manifold
1 Exhaust to intake manifold
5/16 - 24 - Hex head nut
2 Carb to manifold
3/8 - 16 x 7/8" - Hex head bolts
1 Transmission mount to transmission (depends on tail stock &
mount)
3/8 - 16 x 1" - Hex head bolts
2 Generator mounting bracket to block
3/8 x 1" - Hex head bolts & nuts (GRADE 8 - pitch not critical)
4 Motor mount to chassis tower
3/8 -16 x 1 1/2" - Hex head bolts
6 Transmission to Engine
7/16 - 20 - Hex Nut
1 Transmission mount to chassis mount (if required)
3/16" clamps
9 Fuel line
8 Electrical
5/16" clamps
20 Hold wiring harness to body
1/4" clamp /w speednuts
1/4" clamp /w speednuts
10 Hold hydraulics to chassis, etc.
Since there are several way to get here, to return to where you came from, please use the "BACK"; button on your browser.
To email me with comments or questions.